#customfeature

is there a way to know in FS if the tolerant dimension is active?
I've started implementing the UIHint_CAN_BE_TOLERANT in my relevant custom features. one of them is the makeRadius FS wich can set a cylinder or conical surface at a certain radius. if it is a conical surface, my edit logic will add a required query for an edge to measure and set the radius at. I believe only cylindrical…
new custom feature: Boolean Variable
Happy winter solstice to everyone! I was grouping some dynamic suppressions in a configurable document and creating a regular variable, setting it to 'any' and creating an equation, (or typing "true" manually.) This bothered me, I figured this should be easier if I'm going to do this a lot. so I created a dedicated:…
Old/New custom feature: Intersect+ (a.k.a. Subtract complement)
This feature is so easy to code that there are probably many of them, but due to custom feature's being hard to search/find and names aren't always as clear, I did so once over a while back. I just took the effort to add an icon, a pdf and publish it so it might be easier to find for others: Intersect+ (a.k.a. Subtract…
I need a bit of help.
Im trying to make an interlocking foot for a table. It should slide but also be lockable. The foot has a tooth that locks into the upper part (dark grey) . The upperpart can be elevated to unlock the foot and to drop it. Now my problem: every slot in the upper part should be at a specific angle so that the tooth from the…
QR Code feature
Feature link: https://cad.onshape.com/documents/590aa2e4425ab6d582393356/w/81d6535fe1c9afe3c44a3424/e/98a77b1588b0b49a23f1a7dc This feature extrudes geometry representing a QR code. Notes: * Only "normal" ASCII characters are supported as input. No Kanji mode. No micro QR codes. * At the end of the feature dialog are some…

is there a way to know in FS if the tolerant dimension is active?
I've started implementing the UIHint_CAN_BE_TOLERANT in my relevant custom features. one of them is the makeRadius FS wich can set a cylinder or conical surface at a certain radius. if it is a conical surface, my edit logic will add a required query for an edge to measure and set the radius at. I believe only cylindrical…
new custom feature: Boolean Variable
Happy winter solstice to everyone! I was grouping some dynamic suppressions in a configurable document and creating a regular variable, setting it to 'any' and creating an equation, (or typing "true" manually.) This bothered me, I figured this should be easier if I'm going to do this a lot. so I created a dedicated:…
Old/New custom feature: Intersect+ (a.k.a. Subtract complement)
This feature is so easy to code that there are probably many of them, but due to custom feature's being hard to search/find and names aren't always as clear, I did so once over a while back. I just took the effort to add an icon, a pdf and publish it so it might be easier to find for others: Intersect+ (a.k.a. Subtract…
I need a bit of help.
Im trying to make an interlocking foot for a table. It should slide but also be lockable. The foot has a tooth that locks into the upper part (dark grey) . The upperpart can be elevated to unlock the foot and to drop it. Now my problem: every slot in the upper part should be at a specific angle so that the tooth from the…
QR Code feature
Feature link: https://cad.onshape.com/documents/590aa2e4425ab6d582393356/w/81d6535fe1c9afe3c44a3424/e/98a77b1588b0b49a23f1a7dc This feature extrudes geometry representing a QR code. Notes: * Only "normal" ASCII characters are supported as input. No Kanji mode. No micro QR codes. * At the end of the feature dialog are some…

#customfeature

Discussion List