Welcome to the Onshape forum! Ask questions and join in the discussions about everything Onshape.

First time visiting? Here are some places to start:

Looking for a certain topic? Check out the categories filter or use Search (upper right).
Need support? Ask a question to our Community Support category.
Please submit support tickets for bugs but you can request improvements in the Product Feedback category.
Be respectful, on topic and if you see a problem, Flag it.

If you would like to contact our Community Manager personally, feel free to send a private message or an email.

drawing

Drawing Size Restriction Problem

miles_bliey 97 views 6 comments 5 points Most recent by miles_bliey September 17Drawings
Recreating the linked ring in OnShape

Accepted Answer charlie_kingsland 94 views 5 comments 0 points Most recent by charlie_kingsland August 20Using Onshape
Modified off-the-shelf parts

Answered eric_poulson 105 views 4 comments 0 points Most recent by eric_poulson May 19Community Support
Rev Table

wayne_sauder 56 views 4 comments 0 points Most recent by shawn_crocker April 6Drawings
Feature request: perspective view in drawings

johan_van_ravenhorst 877 views 8 comments 35 points Most recent by jacques_spillmann March 31Product Feedback
Mirroring imported image in sketch mode

Answered tony_459 383 views 5 comments 0 points Most recent by matthew_stacy March 15Drawings
dwg's importing slightly off target

derek_westwood 24 views 1 comment 0 points Most recent by dirk_van_der_vaart March 4Using Onshape
How to specify a linetype for a part or assembly when it is shown in a drawing view ?

Question Hans_Ole_Leirvik 44 views 0 comments 6 points Started by Hans_Ole_Leirvik February 4 Community Support
How do I move adrawing view from one sheet to another

Answered derek_westwood 100 views 4 comments 0 points Most recent by wayne_sauder January 28Community Support
Forcing point-to-point dimension to be aligned rather than horizontal/vertical

Accepted Answer alan_budden 45 views 6 comments 0 points Most recent by bruce_williams January 14Community Support
Edge break symbol in Drawings

alessio_hartmann 754 views 2 comments 3 points Most recent by thomas_pedersen704 December 2020Drawings
How do I turn off Ares Kudo?

Answered Kyler_Walker 76 views 2 comments 0 points Most recent by john_mcclary December 2020Drawings
Moving entire sketch after copy and paste

Accepted Answer paxson_matthews 44 views 2 comments 0 points Most recent by paxson_matthews December 2020Community Support
Easy way to replace drawing template in hundreds of drawings?

fnxf 248 views 7 comments 1 point Most recent by Ben_Tek_Pac October 2020Drawings
Place a point to dimension to in 2d drawing

Answered steven_armstrong 195 views 11 comments 0 points Most recent by steven_armstrong October 2020Drawings
How to add dimensions between arbitrary points on a drawing

Answered hannuman_bull 35 views 1 comment 0 points Most recent by john_mcclary August 2020Community Support
How can I create an angle cut out of a cylinder? (sort of like a needle)

Accepted Answer zach_morris 702 views 9 comments 0 points Most recent by zach_morris August 2020Using Onshape
Blind hole doesn't show on drawing, but through-hole does

Accepted Answer david_scott322 94 views 3 comments 0 points Most recent by david_scott322 July 2020General
Is it possible to update a drawing to an updated format/template without recreating the drawing?

Answered mike_sandstrom 74 views 4 comments 0 points Most recent by PeteYodis June 2020Community Support
Drawings 'n dimensions ...

Accepted Answer ella_meunier 66 views 4 comments 0 points Most recent by john_mcclary June 2020Community Support
Display area measurement

victor_lamoine 22 views 0 comments 0 points Started by victor_lamoine June 2020 Drawings
Reuse existing Drawing for multiple remove-extrusions

kvdmolen 175 views 11 comments 0 points Most recent by john_mcclary April 2020Using Onshape

Howdy, Stranger!

It looks like you're new here. Sign in or register to get started.