help
Discussion List
-
How can I pattern this particular shape as such:
I know how to draw the "figure eight" shape, but I don't really know how to get this to pattern in such a way as seen above. Any help would be much appreciated.
- ISEETHATTHEDIFFERENCEOFTHEDIAMTERSOFTHESECIRCLESIS2.8 MM.BUTTHEDISTANBETWECIRCLES'EXTREMITIES ISNOT
-
Strange Undefined (?) Sketch Arc Never Goes Away
Hi, I'm a student designing for FRC team 2415 and I've discovered a weird error that I don't even understand. I was designing a gusset for our robot when these unselectable, omnipresent undefined arcs appeared in the parts studio. When I checked the assembly I had used the part it, they appeared there too! Only information…
-
Create surface from perpendicular sketches? (making 3D printed mask)
Hello people, I quickly drew up these two sketches for a snake design mask and would like to know how I could possibly use both to form a surface which I can thicken later? Image below should hopefully explain better: The front plane sketch is the main front facing design, and the right plane is just one spline sticking…
-
Non-Hybrid Modeling
I am a professional engineer with over a decade in modeling experience on multiple platforms (solid edge, solid works, Inventor, and Catia). A large part of my experience with complex modeling was using CATIA with which I excelled with robust design models. During this time, I almost exclusively used what I have come to…
-
How do I model a shape where the bottom face differs from the top?
Hi everyone, I’m still quite new to Onshape and I’m trying to model a part based on a hand-drawn sketch: So far, I’ve created the top face as a 2D sketch: However, the bottom face of the part is different from the top (highlighted in yellow in the first image), and I’m not sure how to create this correctly in Onshape.…
-
Problem with extruding shape
If I try to extrude my sketch, it doesn't work, and OnShape is not telling me why. Please help! Thanks in advance!
- beginner Here, can't figure out how to make a hemisphere or sphere. thanks!
-
Issue with controlling direction of asymmetric fillet
Hi all, Having some issues with the asymmetric fillet feature in part studio. Only one of the edges is reversed in its direction, and I can't seem to find a way to edit or control this. Does anyone have any suggestions? Are the rounded corners causing this issue? (Corners done in a previous fillet feature, not in a sketch)…
-
How do I make a Loft of sorts that will make a "curved ramp"?
I want to fill that area with a loft of sorts, that respects the curvature and "eases" the ramp until it reaches the end. How may I do that? https://cad.onshape.com/documents/95348026f22336243da5298c/w/4954531794b31370f3012f6a/e/9ff6052f079dd476ea8925f3?renderMode=0&uiState=67e749df5017516de822cc39
-
assistance needed
https://cad.onshape.com/documents/5e0aad5338049d58e998649d/w/4329a036c2204f750e842286/e/cc4f8ca8c6a8753bb66f7bdf?renderMode=0&uiState=67e60a11f2c902141a6ae0e7Error hello all this is a house i am working on for a school project and i am not sure how to solve the errors if anyone can assist please comment your email and i…
-
Issues with loft function
Hello, I’m quite new to Onshape, and I’m having some issues with the loft function. I’m trying to create a propeller blade (3 cm wide) and add a twist to it. I’ve made curves that the profile should follow, and I used airfoil generators to create the NACA profile. However, whenever I try to use the loft tool to make the…
-
Why is my clamp locking when I bring it all the way forward or back?
I have finished this project bar one detail, when I bring the arm mechanism all the way to the front of back it becomes locked and I have to press undo to get it back. I have been stumped on this one for a while. I have attached photos of the clamp below of it in it's starting position and then it in it's locked position.…
-
Why is my clamp locking when I bring it all the way forward or all the way back?
I have finished this project bar one detail, when I bring the arm mechanism all the way to the front of back it becomes locked and I have to press undo to get it back. I have been stumped on this one for a while. I have attached photos of the clamp below of it in it's starting position and then it in it's locked position.…