help
Discussion List
-
How do I blend the two inside faces too each other? I can't seem to get face blend to work. Plz Help
https://cad.onshape.com/documents/c5684b823c04af1ec354a756/w/4360f2a9b3dae329827ae9f2/e/e1df25300d4c I want to blend a face between the outer perimeter of the center piece to the inner perimeter of the outer piece and can't seem to setup a face blend. Am I doing it wrong? is there a better function to use? any help would…
-
Surfaces Won't Turn Solid
Hi, I am relatively inexperienced with working with surfaces in Onshape, and have ran into problems when trying to make them solid parts. I am designing a logo that uses hundreds of surface lofts to enclose the top and bottom plates, but the enclose tool doesn't work for me and I run into issues in many of the surfaces…
-
Best practice when updating and versioning a FeatureScript
Community, I searched the forum, but did not find any messages that address my question. I have successfully created a FeatureScript, versioned, and shared it with my FIRST Robotics teams. Now I want to make enhancements. Are these the best steps for a new FeatureScript version? Create a new Feature Studio in the original…
-
Replace instances of a linear pattern with new part or configuration
Hello! I am trying to make a configurable grid. I have a single cell designed up and have configurations controlling the length and width. The grid can be 1x1 up to 6x6. I am trying to change the configurations of the corner instances to a configuration of the base cell with a rounded corner. I am also trying to add a…
-
Making a bend for an extruded object
I made this model and would like to bend it for 45 and 90 degrees left or right. Is there a way to bend an extruded part similar to what the loft functions do? Thank you in advance!
-
Best way to pattern Honeycomb part
Hello, I'm looking for the best way to make a Honeycomb wall. unfortunately my part has some "complex" geometry so I can't seem to get the fill pattern tool to work. I started by created a single cell and then orignally did multiple linear patterns to form the wall. I have tried this 2 difference ways one taking 8.91…
-
Improve surface of complex shape
I try to create the head of a fantasy panda. The result is not as smooth as I wanted it to be. So I'm asking you if you recognize mistakes or space for improvement. For that I'd like you to quickly guide you through my process: I started with this sketch. The head consists of two splines. I made sure the had the same angle…
-
Sketches won't loft
I am trying to get the two faces in my document to loft be each time I try the inner profile just goes red. No idea how to fix this, would really appreciate some help. https://cad.onshape.com/documents/a029e4e0f14f06e8c8efb638/w/5c0b632cb8f6c2a9d3d007c4/e/e7762b37295653af6d83ecfc
-
Onshape is unnecessarily lagy, What can I do to fix this.
Despite following all recommended troubleshooting steps provided for improving performance, the issue with Onshape remains unresolved. All suggested fixes have been implemented, I have also check my system throgh onshape at it is fine. Diagnostic tests indicate that the hardware and meet all required specifications, with…
-
drawing is printing a lot smaller than object measures in onshape
I apologize, I'm new at this, so I am still learning. I didn't want to ask for help since I need to know this, but I've tried for the past 3 days and I'm getting no where. I get everything created in Onshape, export it to an STL file, and open it in Bambu Studio. When I go to print it, it is less than half the indicated…
-
skArc/Constraint syntax and radius calculation error
Hi! So I'm trying to create a custom feature and i've found a problem where i try to create an arc using 'skArc' and later define it using 'skConstraint' with '"constraintType" : ConstraintType.RADIUS' but while the original points defined in "start" and "end" are correct in the part studio the "mid" point and therefore…
-
Can't figure out CANNOT_RESOLVE_ENTITIES from opBoolean
I've been going through the FeatureScript Fundamentals course in the learning system, and I'm on the final exercise. I'm getting a CANNOT_RESOLVE_ENTITIES from a opBoolean call, and I can't figure out what going wrong. I've more than triple checked my code against what's provided in the instructions, and I've added debug…
-
how to fix issue when drafting with extrude remove
i'm trying to remove solid extrude my initials from a part, with it drafted inward, but it won't work, despite it working with the exact same setup, but different parts, on 5 previous documents. my initials were the exact same height on all 6 documents, and they all have plenty of extra room to extrude, yet it keeps giving…
-
Why isn't the coincident constraint working right?
Applied a coincident constraint from this construction line to a spline, yet it created this micro gap which I didn't notice until I really looked. This later caused issues for me when I went to make a projected curve and the shape not filling in properly as its not an enclosed loop. The sketch is entirely fixed, no points…
-
How can I add a draft angle to this complex shape?
Hi, I'm very, very new to CAD. I'm a chocolate maker trying to design my own tools for vacuum formed chocolate molds. Right now, I'm struggling to add draft angles to my shapes. I finally figured out how to import the image, trace it and extrude it, but following the advice from the AI (to copy the sketch, enlarge it and…
-
Sweeping Along a Cylinder (Normal to the Surface)
Hi, I would like to sweep a slot on a cylinder that will be CNC'ed. The slot needs to be normal to the cylindrical surface as it wraps around it. I tried sweep and wrap and neither wrap normal to the surface. Closest example of what I need - Imagine as you turn the grey part, the grooves mate with the tabs on the outlet.…
-
Sweep angle to face
Good day everyone, I am novice designer and have been trying to learn Onshape since I graduated from undergrad. My first self project was to recreate a simple distillation apparatus. However I am having some issue, trying to create the condenser part. The condenser should pierce through the cylinder until the inner wall.…