slot

Anyone already wrote a feature script for "slotted bending" (sheet metal)?
Hey, I am currently trying to write a quick feature script to transform a sheet metal bend corner into a "slotted bend" (like described nicely over at Hackaday a while back: https://hackaday.com/2016/05/18/the-art-and-science-of-bending-sheet-metal/ ). This can already be easily done manually by drawing a sketch with a…
How to design slots of different sizes/depths/widths in solid piece?
FFCP2 Tool Holder | Part Studio 1 I'm trying to 'simplify' the design of a tool holder for my 3D printer setup. It's just a tilted block of plastic with slots for a spatula, a pair of needle-nosed pliers, and a side-cutter. The attached photo shows the original design, but I want to redesign it so the block is tilted up…
Best way to place a construction line from offset of circle centre to circumference?
If I want to place a slot which is in-line from the centre of a circle, and is an offset from the centre and from the circumference, the only way I can work out of doing this is to first draw a construction line from the circle centre to the circumference, then overlay a second construction line on top of the first, this I…
I'm having trouble with the Slot tool
I'm not able to make an accurate enough measurement in the screw holes for this part https://cad.onshape.com/documents/5ea02c7708d3e42bf5c7c22b/w/1590be5a74c3a8daa0f2e085/e/34f4a2c4e6a21a816c63b69f so I'm trying the Slot tool. I opened the sketch named "sketch of vise jaw face". I added a small horizontal line centered at…
machined crank slot I tryed a projected curve , it is similar to a ford typ a crank shaft.
Not able to snap the mate connector to the center of the slot
Hi, I want to mate the center of the slot with a hole on another part. When I hover the mouse on the surface near the slot I see all the snapping points (as shown in the picture below). The problem is when I hover the mouse to the center point everything dissapears. If I move the mouse around the slot, I get to select…
Example create a slot feature code, doesn't go through part
When I try the example slot code https://cad.onshape.com/FsDoc/tutorials/create-a-slot-feature.html with an extruded object with a second end point in the same direction as the first the slot doesn't go all the way through the object. For an extrude of 25mm the second extrude has to be 5mm or more for this behaviour to be…

Anyone already wrote a feature script for "slotted bending" (sheet metal)?
Hey, I am currently trying to write a quick feature script to transform a sheet metal bend corner into a "slotted bend" (like described nicely over at Hackaday a while back: https://hackaday.com/2016/05/18/the-art-and-science-of-bending-sheet-metal/ ). This can already be easily done manually by drawing a sketch with a…
How to design slots of different sizes/depths/widths in solid piece?
FFCP2 Tool Holder | Part Studio 1 I'm trying to 'simplify' the design of a tool holder for my 3D printer setup. It's just a tilted block of plastic with slots for a spatula, a pair of needle-nosed pliers, and a side-cutter. The attached photo shows the original design, but I want to redesign it so the block is tilted up…
Best way to place a construction line from offset of circle centre to circumference?
If I want to place a slot which is in-line from the centre of a circle, and is an offset from the centre and from the circumference, the only way I can work out of doing this is to first draw a construction line from the circle centre to the circumference, then overlay a second construction line on top of the first, this I…
I'm having trouble with the Slot tool
I'm not able to make an accurate enough measurement in the screw holes for this part https://cad.onshape.com/documents/5ea02c7708d3e42bf5c7c22b/w/1590be5a74c3a8daa0f2e085/e/34f4a2c4e6a21a816c63b69f so I'm trying the Slot tool. I opened the sketch named "sketch of vise jaw face". I added a small horizontal line centered at…
machined crank slot I tryed a projected curve , it is similar to a ford typ a crank shaft.
Not able to snap the mate connector to the center of the slot
Hi, I want to mate the center of the slot with a hole on another part. When I hover the mouse on the surface near the slot I see all the snapping points (as shown in the picture below). The problem is when I hover the mouse to the center point everything dissapears. If I move the mouse around the slot, I get to select…
Example create a slot feature code, doesn't go through part
When I try the example slot code https://cad.onshape.com/FsDoc/tutorials/create-a-slot-feature.html with an extruded object with a second end point in the same direction as the first the slot doesn't go all the way through the object. For an extrude of 25mm the second extrude has to be 5mm or more for this behaviour to be…

slot

Discussion List