-
PEM Hardware information in Hole Callouts
Hi there, I was wondering if anyone has any interesting work arounds for including PEM fastener information automatically in the hole callouts on holes made using the hole tools PEM features. Or any work flow tips for including PEM Callouts in Onshape drawings. Right now I am adding manual notes to call out the specific…
-
Hole diameter precision in drawing hole table
The hole table properties allows setting the hole location precision to 3 digits, but there's no option to set the hole diameter precision. I can make the hole diameter precision 3 digits in the table by setting the drawing default to that. I would prefer to use a drawing default of two digits, otherwise I have to…
-
Hole table
I have a simple plate with a few holes. When I select Hole Table I get the little dialog box, but I'm unable to click on a view. There is no response when I hover over or click on the only view in the drawing. Yes, the holes have been created as hole features (not extruded/removed). Here's a link to the…
-
Flat-Head Screw Hole
How do I place Flat-Head Screw Holes on a curved surface? I need to specify the location so that they align with the mating part. I have included a simple sketch and would like to add the holes on the inside of the part so the screws point outward.…
-
Countersink hole from opposite face
The above is an extruded shape. I'm using the Hole feature and the points for the holes have been drawn on a plane derived from the "bottom" of the shape. Thus, the countersink is at that location. I'd like the countersink to start at the opposite face, to create a countersunk "pocket" hole in the curved face. The hole is…
-
Countersink with M3 and bigger only?
I'm trying to make M2.5 countersunk holes, but I don't get the chamfer on them (or smaller), while I do get it on M3 size and bigger. Here's a test document: https://cad.onshape.com/documents/ec5b355b32308a201247974a/w/22bc19797fcb30004dea4b95/e/e62ee5e5019dd294ac17a4c0 The dialog for M2.5 here shows the same value for…
-
holes to points in circular pattern
i want to do holes. i created points in a circular pattern as the center for the holes. no i have difficulties defining the locations and the scope in fs for the holes. const anzahl = dimensions.Rotation; for (var i = 0; i < anzahl; i += 1) { const t= rotationAround(rotationAxis, (2*PI* radian) * (i/anzahl) ); const…
-
How to repeat a hole on the other extreme of a wooden beam
Hello all, I must first be warning you that you are facing a complete and total beginner on 3D modelling.I'm currently trying to finish a training wall intended for dog training, that has been around the web and it's known as a Schutzhund A Frame Wall. Here's the project I'm basing off:…
-
Relif Cut
Hello, is there an automatic function to make a free cut for holes that are too close to the bending edge? Once constructed an example. https://cad.onshape.com/documents/17763e1bca9abe8f571334e7/w/4e6c4b1da9827dde10ae8531/e/209f66484bca7a61ca701914
-
Using hole feature in square tube
I often need to sketch a hole in one side of a rectangular tube which doesn't penetrate the opposite side. Usually I just pick a hole depth which insures full penetration of the near side but doesn't penetrate the far side. This seems wrong and it is confusing laser cutting shops. I should be able to choose "up to face" or…
-
How do I correct holes that are on the wrong axis?
Thanks to some previous help here, I have managed to cut some holes using the hole tool but depending on the orientation of the part the holes end up incorrectly positioned. Not actually an issue currently as I will always work in one plane but I would love to make the feature universal for future proofing. Correct holes:…