-
How to remove several constraints at a time?
I often want to revisit a previous design and make small changes, tune the dimensions, etc. But every time I do that, it ends up over constraining the sketch, or some similar issue. How can I remove all (or several selected) constraints in a sketch, all in one go? As opposed to clicking every single one and do it…
-
Exporting a sketch as a DXF?
Hi everyone - I am somewhat competent with OnShape and creating basic 3D things but I am struggling with a new project I am working on. I want to make some cribbage boards on irregularly shaped wood using my laser to mark the dots on the wood so I can drill them out. What I am trying to do is use a spline to create the…
-
Pattern on a sphere
hi pretty new to Onshape and cad it self by like that u Can design things and I get better all the time. my wife has this clock witb a nice pattern and really want a patten like that on a sphere also and maybe other things But sad to say after a few (lot) tryes its more than I Can at the moment 😔 Can anyone lead me the…
-
Keep edges when extruding split line as surface
Does anyone know how I can keep the edge when extruding a sketch with a split line as a surface? Here is an example of what I am talking about:
-
Sketch could not be solved - Maximum size sketch
Hello, I am reaching out because I am experiencing an issue with one of my sketches. I was creating something like a pipeline/tube, and at some point I started to run into problems with my sketch, as ONSHAPE reported me that it could not be solved. However, I was quite confident about my constraints. After investigating, I…
-
when a sketch is not fully defined, is there a way to change the highlight from blue
I have a difficult time discerning blue from black in the user interface. It would be nice to be able to have those issues highlighted in an easier color.
-
Help Regarding Feature Creation in OnShape
I am trying to replicate a feature from this YouTube video at the 55:07 timestamp- The problem I encountered is that the creator is using PTC Creo and using the Face Blend feature. I was unable to match a same feature on onshape so I used the loft feature and created splines as guide curves in order to create the feature.…
-
Can I add notes to a sketch within a part studio
I know we can add comments, but is there way to add notes to a sketch itself, similar to when doing 2D drawings. Example: Say I add some drawing lines for a component I want to use, a simple outline of the part to show size and location. It would be nice to be able to point to it with a note that contains the parts…
-
How to make cutouts on sphere follow the curve?
Hi everyone, I'm trying to make a model of a smooth tennis ball, but I have no idea how to make the curved grooves on it. Is there some way to sketch out the curve and project it onto the sphere, then sweep/extrude out the cutout? Thank you.
-
Export sketch as piecewise polyline.
It's been a while since I've written any featurescript. I'm looking for the following solution. I would like to be able to select N closed and open chains of sketch entities and with a provided tolerance tesselate them into N piecewise polylines and then either print them to the console or copy them to the clipboard. Is…
-
Make extrude removal stop before walls get too thin while maintaining a consistent cross section
Hello all, I am trying to make a leeboard hydrofoil model on this document: https://cad.onshape.com/documents/40a09d2b7dbc0e96f864de60/w/9b820e6caf97b342e0b34d33/e/e4addd4030400b4f4e982b63?renderMode=0&uiState=687bf140abce191eed0df80b This will be 3D printed with carbon fibre spars inside it, and I have been struggling to…
-
Creating a hole on the top face of a sweep
I'm new to 3D design, an onshape therefore as well. I have a design I'm trying to make: https://cad.onshape.com/documents/4f3068fc37cd404e496b5d65/w/bb2460c448ccdfc772293d47/e/0a043b966426950f70e23de1Error If you look at the bottom, there are two drilled holes extending into the part, based on two vertexes of a line…
-
Strange Undefined (?) Sketch Arc Never Goes Away
Hi, I'm a student designing for FRC team 2415 and I've discovered a weird error that I don't even understand. I was designing a gusset for our robot when these unselectable, omnipresent undefined arcs appeared in the parts studio. When I checked the assembly I had used the part it, they appeared there too! Only information…