Welcome to the Onshape forum! Ask questions and join in the discussions about everything Onshape.
First time visiting? Here are some places to start:
- Looking for a certain topic? Check out the categories filter or use Search (upper right).
- Need support? Ask a question to our Community Support category.
- Please submit support tickets for bugs but you can request improvements in the Product Feedback category.
- Be respectful, on topic and if you see a problem, Flag it.
If you would like to contact our Community Manager personally, feel free to send a private message or an email.
Onshape Forums
Discussion List
-
Creating Zig-Zag pattern split on cylinder
Hi, I'm trying to recreate an stl, and one of the things I'm trying is to split a cylinder using a zig-zag pattern like this through the cylinder Y Axis. Here's the doc: https://cad.onshape.com/documents/1671297e6cd1347a60024bb9/w/8056e634dd18d6b45ac4967c/e/2744bcd8ea374c73df758837 I tried creating a tangent plane from the…
-
How to visualize cut features
Hey everyone, I'm working on a FeatureScript that cuts both a bolt hole and a nut slot in one feature, according to my specific needs. The feature itself is working great so far. What I am struggling with is: I am trying to figure out how to best visualize the hole that's being cut. Typically, most of the holes' geometry…
-
Fitting hinge to the case
Hello, I'm very beginner, and I would like to fit the hinge to the case by their midpoints. How or which mate type is ok for this fitting ? Thanks for you answer in advance Csaba
-
How do you fully define a spline?
Hi! I am trying to approximate an involute curve by connecting the end of these lines with a spline. However, the points on the end of the spline are being reported as "loose ends", and I am not sure how to fully define the spline with the necessary constraints. Originally, I speculated it was because I had not constrained…
-
Shelling a part with multiple features.
I am try to shell the inside of this part without all the extraneous remnants. Any suggestions. https://cad.onshape.com/documents/bc8497324d4bbc20d036cc2c/w/a92e26e553b7a900556e45dc/e/910fe6b8f10bb9e48eb0e9f9
-
struggling to get sheet metal finish model to allow me to select the sweep to mirror
https://cad.onshape.com/documents/d5c6fd306f2176785c8372c7/w/44001d94a54996c5313e6987/e/a7184476739d4d542b57d52a It seems like the sheet metal finish model feature has not shut down the sheet metal mode. Must be missing something here. Thanks guys
-
How to best mate a single bend putter shaft to a putter head
Hello, I have a mate connector/assembly problem that Im looking for help with. I am trying to attach a putter shaft that has a single bend to a putter head. I care about a few key constraints, other than that I want the rest to be derived from the constaints: Shaft offset relative to putter head (Y distance) "piece point"…
-
Problem with Parametric Curve FS
I'm trying to use the parametric curve FS but have some issues. My variables (N, R, r, E) are set as numbers. I also have the Define Parameter FS set as t. I'm not too sure why it's giving me an error (failed to regenerate). Is there something wrong with the formula I input, like the /1mm part or something else? I attached…
-
How to make the transition from a chamfered edge to an unchamfered edge?
I'm modeling a porch column in Onshape. The top and bottom parts are square in cross-section, extruded from separate planes. The middle part is an octagon in cross-section (basically a deeply-chamfered square), extruded from a separate plane. Between the parts are short transitions where the octagon becomes square, where…
-
How to smoothly transition oblique 90 corners perpendicular to a curving Fillet
I need this face to lay down and smoothly transition the rest of the part into the Fillet but I can't seem to figure out how to do it. Any ideas?
-
Loft with 2 profiles and multiple edges in each profile?
I have two arrays of edges for top and bottom faces, how do I use opLoft() function to create a single surface around the edges between top and bottom faces? At the moment I can iterate the arrays and create separate lofts between two edges, I'm looking for a way to make it as one loft. Thank you.
-
曲面展平功能
曲面展平功能怎么用?
-
Why is my clamp locking when I bring it all the way forward or back?
I have finished this project bar one detail, when I bring the arm mechanism all the way to the front of back it becomes locked and I have to press undo to get it back. I have been stumped on this one for a while. I have attached photos of the clamp below of it in it's starting position and then it in it's locked position.…
-
GeometryType.SURFACE error
Hello, I was trying to implement a function to select a gore created by a loft, and i wanted the user to select the different gores to add an offset surface. But when I add the GeometryType.OTHER_SURFACE, I have this error. I heard about using qGeometry but I don't know how to use it and when. If someone can help me, thank…
-
Layer export
Hello, When exporting an OS drawings as a DXF, the file contains many layers. Is there a way to access these layers to modify/control them in any way? Thanks,
-
Filter out faces that "touching" sides?
Hello. I have a list of triangular faces, how can I remove faces that are touching edges of other faces, leaving only triangles that touch each other at the corners?
- drawings are slow, how can I speed up the loading times?
-
Loft issue
I am creating a loft between a rectangle and a circle, and I would like the surface of the loft to be flat topologically speaking so that it can be made out of one piece of sheet metal (so that it doesn't have to be stretched). It seems that Onshape goes for minimum surface area or something instead. Here is what I am…
-
reusing a sketch in featurescript
I'm working on what will be a template to 3d print and then used for routing some plywood. One of the basic issues with machining is of course the tool diameter and thus the fillets created in corners. I thought it would be interesting to make a reusable feature to reapply some corner relief to address this. I have already…
-
DISAPPEARED DRAWINGS ON DOCUMENTS
All of a sudden my drawing in part studio disappeared, although it is still visible in the assembly page. How to solve ?
-
Stand-alone part extrudes, but not when added to the main part - Issue is back again
I am barely more than a novice. I am working on a simple form: When The internal supports sketch is extruded as a new part, it works great. When I change the extrusion to Add and merge with Part 1, It becomes non-manifold. I don't understand why, or how to fix it. This problem went away for part of a day, but now it is…
-
Select Other on ipad
Hi, I'm using my ipad pro with a keyboard, the Onshape application and a mouse. I have two lines in a sketch - one on top of the other - and I want to select 'the other line'. I have tried pressing the ` key, the @ key and frankly, i've tried every single other key on the keyboard. I've also tried right clicking, centre…
-
hot to change alot of part colors in onshape?
basically my team decided that our team color scheme was going to be orange and white a month ago but now suddenly everyone wants to change the colors it black and blue. we are a new team and I already have the robot cad-ed in orange and white and I really don't want to manually change all the colors. is there like a way…
-
How to I change the units for density?
Hello, Under "My Accounts > Preferences > Units," there's no option to change the default unit for density, even though there are options for many other parameters that could be derived from the basic units (length, mass, time, etc.). Originally, I had mass set to pounds (lb), and I reset it (and saved) to grams and later…
-
Why is my clamp locking when I bring it all the way forward or all the way back?
I have finished this project bar one detail, when I bring the arm mechanism all the way to the front of back it becomes locked and I have to press undo to get it back. I have been stumped on this one for a while. I have attached photos of the clamp below of it in it's starting position and then it in it's locked position.…
-
How can I sketch curved text?
Hi, I like to use OnShape to create DXF files to laser cut. I have been trying to create a circular perpetual calendar but have been unable to curve the text to follow a curved line as its base line. Additionally, is there a way to import fonts into OnShape?
-
how to i fix this error with the sweep?
link here: https://cad.onshape.com/documents/0785323e3fd6693c96128604/w/cf64c6ba56382a7e3568eb93/e/406d8f78a767e7942a224627
-
Fully Constrained Sketch Not Extruding.
Getting the error of "Missing Face of Clip" when trying to extrude a fully constrained sketch.
-
ThreadCreator UNC thread
Hi, is there a way to create a 1/4" UNC standard thread with Thread Creator? I would like to print some support with 1/4" camera mounting screw.
-
How do I remove unwanted bend dimensions from a drawing?
I have tried right mouse clicking on it and just hitting the delete neither work.
Categories
Popular Tags
- featurescript 890
- drawings 614
- assembly 444
- sketch 429
- assemblies 379
- improvements 358
- help 331
- part studio 322
- configurations 307
- feature script 301
- Sheet Metal 296
- drawing 254
- how to 250
- feature request 242
- mate connectors 235
- loft 216
- export 209
- api 200
- dimensions 199
- extrude 196
- sketching 195
- voting 187
- variables 180
- improvement requests 174
- mates 162