Welcome to the Onshape forum! Ask questions and join in the discussions about everything Onshape.
First time visiting? Here are some places to start:
- Looking for a certain topic? Check out the categories filter or use Search (upper right).
- Need support? Ask a question to our Community Support category.
- Please submit support tickets for bugs but you can request improvements in the Product Feedback category.
- Be respectful, on topic and if you see a problem, Flag it.
If you would like to contact our Community Manager personally, feel free to send a private message or an email.
Onshape Forums
Discussion List
-
Introduction to Sketching training difficulties
I am doing your training Introduction to Sketching but when I try to enter the base dimension I get an error. "Sketch could not be solved" I have tried to restart the project several times, checking each step in detail. I was unable to find a solution to this issue. Could you help me overcome this problem? Thank you in…
-
Will a 3d printer print 3 separate parts as 1 part if fastened?
So I wanted to print something that is made up of 3 parts fastened together through fasten mates however I wanted it to print as 1 part. Will this be able to print as 1 when exported and if not how will I do it?
- why is the square not fully defined?
-
Loft or Sweep Triangle Shape around Cylinder
Hi all, I am looking for a bit of advice on how I can loft from one triangle on the base of a cylinder to a smaller one on the top whilst flowing around a curve on the outer face of the cylinder. I have tried to create some paths around the cylinder but I am unable to get the lofted triangle to 'hug' the cylinder and…
-
Onshape is not connected
Hi, on our school network student accounts get the error "Onshape is not connected". We do not have the option of turning off anti virus (and in any case staff have antivirus but it works on staff accounts). Are there any settings you can suggest trying to make the site work for our students? Thanks
-
Dealing with subassemblies in an assembly
Hey folks, I'm struggling to deal with subassemblies effectively. I used a part studio to create the multiple parts that make up my design but they are intended to be assembled into a number of subassemblies which are then in turn assembled into my final main assembly. This feels like assembly 101 to me. But I have two…
-
Reason for body draft failure?
Body draft seems to be a fancy feature, but I never get it work. Here are 2 examples. Example 1: Body part fails to generate unless those 2 surfaces under red lines are excluded. On the other hand, draft command can finish the same task as expected. Example 2: When there is a step, body draft does not work unless I exclude…
-
Some feedback on the Intro to Design Course
First — thank you for the course. The free education is worth the work required. That said, I ran into a clarity issue that took me a long time to figure out, so here's my feedback: In the Introduction to Part Design Course In the Feature Creation / Exercise: Extrude Going from step 6 to step 7 When you select the back…
-
Exporting parts as single meshes instead of many sub-meshes.
Hi there. So, I'm trying to use the GLTF exporter to transfer my Onshape models to the Godot engine for viewing purposes. Coming from Inventor, I was initially really excited to be able to go directly to GLTF and skip the 3DSmax -> FBX steps, but I'm running into a roadblock. It would seem that instead of creating a single…
-
One or more tabs being moved contain workspace references. All referenced tabs will be moved as part
So what does that mean ….seem like I can not move anything with that note.
-
How to programmatically find faces which define the entry and exits for a hole?
I am working on a featurescript to add internal bosses to threaded holes (this is an evolution of a 3D-printed "tapless" threading posted on youtube). Script: https://cad.onshape.com/documents/1e451ed1452487dd6118fbbe/w/76456d124ce9039290f2b923/e/d5a5f79d9a758c2c8ecf5ab6 Basic concept:…
-
Moiving school education account
I'm moving school later in the year is there a way to transfer my current eduction account as I have many of resourses lessons on there to another school email, or personal acount to hold until the move takes place as there will be a gap?
-
Optimization Solver - New Feature on fs.place
I've gotten a number of request over the years for features that have a measurement based constraint such as perimeter or area. The topic has also come up on the forums a few times (https://forum.onshape.com/discussion/18610/how-can-i-use-perimeter-as-a-constraint). My answer to the question has always been - to optimize a…
-
Worm Gear or Spiral
Hello, I'm making a helix worm like in the picture. However, there is difficulty in determining the angle of inclination of the thread. Can anyone help me? https://cad.onshape.com/documents/536e9d0ebf53bab60fc1d592/w/965b95592ae2103469fab11b/e/b53e3112cdcc919a6e378bc7?renderMode=0&uiState=6785e0cd4059a663f08e1896
-
Sketch features not showing as fully defined
When I add a new feature to a sketch and then dimension it, it stays blue colored instead of turning black to indicate it is defined. Other than the color remaining blue after dimensioning, the feature behaves like it is defined but it is just visually confusing to know which lines have been defined and which have not…
-
Inserting derived assembly into part studio
There are parts I've downloaded that are assemblies; bearings for example that have inner and outer races, retainers, and balls. When I attempt to insert the bearing as a derived part into a part studio I'm working in it comes in as individual parts. There doesn't appear to be a way to group the individual parts once…
-
incline plane / schiefe Ebene
Ich muss ein Abwasser Kanal konstruieren. Ich habe 2 Kreise auf 2 Ebenen (z Achse). Die Kreise sind aber X und Y verschieden. (also kein senkrechtes Rohr) Wenn ich nun den Befehl Ausformung nehme, macht es etwas, aber das Rohr ist ziemlich "schief". Also möchte ich auf einer Hilfseben zwischen den beiden Kreisen einen…
-
Is there a way to always have the "show expressions" option on when entering/viewing a sketch?
I'm working on a object with a lot of parametrization. On some parts, numbers don't really mean anything right now/I'd like to see the expressions, but I always have to activate that setting when entering a sketch. Is there a way to enable the "Show expressions" by default? Or per sketch/document?
-
If I sketch a line in Onshape Drawing for example 200mm how can I change it to be 250mm ?
My main question is if you can change length of line you make in Drawing mode?
-
I imported my DGW file for the template but it apperas very small, how can i increase it?
I want to know if there is any scale command.
-
Can I hide a plane or something through an API?
On Onshape, I can right-click to hide it I have already tried this /partstudios/d/{did}/{wvm}/{wvmid}/e/{eid}/features But I found that hiding and not hiding request results are the same
-
I really like the new front page before you log in.
Hello all, I look at these opening pages with interest these days and I was wondering if these drawings are publically available? I tried searching on the previous few that have come by, but to no avail. I would like to know if it is possible to actually post a link under these projects for us to see and look at in a…
-
Training Question
I am trying to copy out a public file to use in training module. Why does the copy screen grey out and not allow you to browse to folder for placement of your copy?
-
How Do I Make a Hollow Cone at the End of a Hollow Cylinder? I Keep Getting an Error with Revolve
Hi - I've blown most of today trying to do something that seemed simple at first and would appreciate any tips. I am trying to make a hollow tube with a cone at one end and I can only make a solid cone using Loft. It seems impossible to revolve even just a triangle - I keep getting an error regarding Revolve creating a…
-
How to remove a wedge of material?
Hello, I am trying to make a wall mount bracket and am working on the female part. I am trying to make something similar to the image attached, but with some changes. The current part I am struggling with is making the wedge space for my mount to rest on. I have side wedges to slide on, but wanted the superior wedge for…
-
keyboard keys disabled or bugged?
Hi everybody, can anybody help me with this? I was doing some surface modeling on this project of mine yesterday evening, when suddenly hotkeys and even normal keys like shift, control or delete don't respond in the work space. But I can use all keys normally when typing in the dimension tab. Even in other documents I cant…
-
Intro to Part Design basic question
I took Onshape basic online training about four years ago and happily used the platform to create some useful parts. After some time away, I recently came back to create more parts and am now taking the "CAD Basics" course as a brush-up/refresher. However, I'm finding it more difficult than the first time around, starting…
-
Laggy Rendering of Parts in Assembly - How to Solve?
I have noticed that my top-level assembly has recently begun to render in odd ways when viewing it, especially when orbiting or zooming in and out, as you can see in the screenshot I included, None of my other assemblies or part studios behave this way (though they are smaller). Parts also appear to black out in some…
-
Create a gear teeth on an oval ring gear
I'm trying to put teeth into a oval ring gear. Similar to something like this picture. I can make the outside oval, but for some reason cannot make the teeth and pattern it around the oval. I also have a larger ring and many more teeth so making them individually would be a large task. Here's my doc.…
-
Diagonal grid patterns on a curved surface.
Hi, does anyone know of a tutorial on how to produce the pattern seen in the attached photo? Both on a flat and curved object? Thanks in advance.
Categories
Popular Tags
- featurescript 890
- drawings 614
- assembly 444
- sketch 429
- assemblies 379
- improvements 358
- help 331
- part studio 322
- configurations 307
- feature script 301
- Sheet Metal 296
- drawing 254
- how to 250
- feature request 242
- mate connectors 235
- loft 216
- export 209
- api 200
- dimensions 199
- extrude 196
- sketching 195
- voting 187
- variables 180
- improvement requests 174
- mates 162