Welcome to the Onshape forum! Ask questions and join in the discussions about everything Onshape.
First time visiting? Here are some places to start:
- Looking for a certain topic? Check out the categories filter or use Search (upper right).
- Need support? Ask a question to our Community Support category.
- Please submit support tickets for bugs but you can request improvements in the Product Feedback category.
- Be respectful, on topic and if you see a problem, Flag it.
If you would like to contact our Community Manager personally, feel free to send a private message or an email.
Onshape Forums
Discussion List
-
Part alignment using width mate
Hi, I'm using the new width mate to centralise a pully in a holder as below: After having setup the width mate what is the correct way to then align the pulley holes? Or should I just use a fasten mate with an offset? Any help appreciated. Thank you.
-
Question: How to use PersistentCoordSystem?
Looking for some clarification on how to use the PersistentCoordSystem type to track transformations applied to an entity. I've set up a document with a minimal example here to illustrate my confusion. In the document, I have created a new PersistentCoordSystem and assign it to a body entity by setting an attribute on the…
-
Extrude curved surface and snapping to model in sketch mode
Hello, i am new to this program but i pretty know lot functions from C4D and few years ago Sketchup, so i gues i should not be so stupid but its 2 days and i still cant find good solution. 1) Extrude curved surface I need to make two small support by extruding two lines on both side. So i was trying to make sketch which…
-
Relative transformation/distance between mate connectors
Is it possible to measure the relative distance and orientation between two mate connectors as expressed in the reference frame of one of the mate connectors? Currently, as far as I can tell, when using the measure tool between two mate connectors in an assembly I can only get the relative distance as expressed in the x,…
-
Holes and Constraints
https://cad.onshape.com/documents/66ec667b69402e78d72be64c/w/5c527241399c46d4f49d969c/e/82cc5fb6ade076d13d29d41b Hello, I attempted to use the Circular Pattern tool to make my four holes in place of where had used the Center Point Circle tool and now I'm told my plane is undefined even though I can't find any blue…
-
Released configurations - how?!
Hello, I am having an issue with configured parts / assemblies once released. The first example is a configured assembly. This assembly has a child assembly that is also configured, with the configuration of the child assembly being a configured parameter of the parent. To give further context. this is a 'dressed' door…
-
What is the most efficient way to align imported geometry to the assembly origin?
Hi! I am a Solidworks user learning how to use Onshape. I have a frame I am building out of 80/20 bars that I am using imported geometry for. This frame will serve as the boundaries for the rest of the components I mount to it, so I'd like to be able to center the entire thing around the origin, so that the origin is at…
-
I designed an ITX board mounting hole stencil but... printer problems
I printed the stencil at 100% scaling, measured actual dimensions on the printed drawing and applied a correction factor in my printer settings. The problem is the printer seems to be squashing the drawing in one axis more than the other, but my printer only provides a single scale field that is applied to both axes. Is…
-
Half of flat pattern view after mirroring a sheet metal
Hi all, newbe here, Just created a new sheet metal part, wanted to insert a flat pattern to drawing but unfortunately I can see only one half of a part instead of whole. What I did wrong or missed something? Help will be appreciated. Marcin
-
I need a bit of help.
Im trying to make an interlocking foot for a table. It should slide but also be lockable. The foot has a tooth that locks into the upper part (dark grey) . The upperpart can be elevated to unlock the foot and to drop it. Now my problem: every slot in the upper part should be at a specific angle so that the tooth from the…
-
Problem with OnShape
Working through the introductory tutorials of OnShape. One command that does not work on my system is the curve constraint command. Not sure what I am doing wrong but it should be a simple double click to turn two segments into a curve. Do this over and again and two lines remain. Not a huge problem but one day I may want…
-
APP Store functionality
So I have worked out how to subscribe to APP store participants and worked through to identify a part that I would like to incorporate in my drawing. I get to the "Import" into OnShape dialogue but get a window titled after the participant and the model requested. How can I get the model to be inserted into my OnShape…
-
Image sizing
I can’t get in shape to resize my picture based on dimensioning something within it. Trying to do the dimension as soon as I import the image but no go. All the tutorials out there show making a line and dimension it then the image will resize but my line goes to the new dimension but the image doesn’t grow with it. What…
-
Frame cut lists from assemblies
Hi, I have Part Studios using frames and cut lists. Frame lengths are set by configuration variables. When I assemble those Parts Studios the configurations are set according to needs. Is there a way to generate a cut list against the assembly configuration? If not, do I need to set the Part Studios configurations to match…
-
Slider mate limits from variables
Hi, I have a linear rail and carriage sub assembly: The rail part studio has a configuration variable which sets its length. The carriage part studio also has a configuration variable which sets its length. The carriage is mated to the rail with a slider mate. Is there a way to set the maximum slider distance using the…
-
STL not exporting correctly in app but will on website
I have designed a draw system which is parametric. Link below. I sent the parameters to 120mm deep, 180mm width and 160mm tall. However the depth was ok but the other 2 parametric came out to 100mm x 100mm. However the website downloaded an STL that i was able to print to the correct sizing. Any ideas please.…
-
How do I dimension an image with different aspect ratio
I am trying to scale this image to the correct dimension but the sketch could not be solved. What am I doing wrong? Is it not possible for Onshape to change the image dimensions?
-
Improvements to Onshape - June 6th, 2025
It's been three weeks and we are back again with an exciting new update. It includes two of our most popular requests and a number of quality of life improvements. Let's dig in. CAD IMPROVEMENTS WIDTH MATE You will find a new Width mate in Onshape assemblies. This new mate makes centering parts in the assembly easier than…
-
how do i share documents with people?
when i type in their name or email, the share button is greyed out
-
Adding volume as a custom property?
Back in January, mass was finally added as automatically computed property. It seems like other properties can be added through FeatureScript. I want to add part volume as a custom property which can then be added to standard drawing notes. How do I do that? Is there a standard way to do this?
-
Logic Driven Feature (New Custom Feature!) 🆕 [Extrude, Revolve, Sweep, and more..!]
. Logic Driven Feature https://cad.onshape.com/documents/82bc8404c8f8741e0fdff6a6/w/350f6b9785ebcd5f6afa958f/e/876b5c7f599013b764a99… . The Logic Driven Feature can be many different features: (Extrude, Revolve, Sweep, etc..) It allows you to control it's suppression based on logic. This feature also contains the Query…
-
How to angle the sides of tabs around a circular base
Hopefully this is an easy question as I have a direct reference STL that I'd like to replicate and then modify. See the STL here: https://cad.onshape.com/documents/d12e3a1303b4fc96fbc5d579/w/ea6ec74fe48123340054da92/e/8d2b02cb799753e609c7f9cf I can't figure out how to make the edge of the tabs 45 degrees, or make an angled…
-
Any "easy" way to give soft edges to this shape?
As distances and tangents are not aligned, can't use tools as fillet to give soft edges Any idea Untitled document | Part Studio 1
-
Fractions of decimal mesurements
Hi, how do I get fractions of a mm.? When I try it changes to the closest mm. ie 10.5mm changes to 11mm
-
Custom Feature: Auto Loft
So one day I got sick and tired of creating so many things in order to loft 2 objects and created this new feature: https://cad.onshape.com/documents/94e2ca3c499ecbba9ccfafe6/w/c35c00116423894cfa81ae88/e/2ee558d2512c5ebe0f9102c1 This feature allows you to loft a surface without having to make another sketch or plane. You…
-
How to animate the motion automatically
Hi, Is there a way to create an automated animation of an assembly? Not by moving parts or assembly with a cursor. Thank you
-
How to make a "shadow" behind a structure?
Hello forum I have made a "lamp" that cast its light on a surface from an angle, and in the "light" path the there is a round pole tube. I would like to have a a shadow all behind the round pole tube where there are no "light", due to the pole is shadowing from the light source. Is it possible? Here is the link to the…
-
How to see my certificate?
Hi, could anyone guide me on how to take a look back on my basic introduction certificate that I have completed. I want to share it but I don't know where I could find it back. Thank you in advance.
-
How can I fillet all the raised edges of this disk radially? (Explained in description)
I would like to fillet all the raised edges of this disc so that the length of the fillet along every point on the edge is proportional to the radius of the disc at that point on the edge. I can try to explain it better if this explanation is unclear. This disc is for a cam of sorts, and there will be a number of shafts…
- How do I extrude this with both sides sharing the same middle line?
Categories
Popular Tags
- featurescript 890
- drawings 614
- assembly 444
- sketch 429
- assemblies 379
- improvements 358
- help 331
- part studio 322
- configurations 307
- feature script 301
- Sheet Metal 296
- drawing 254
- how to 250
- feature request 242
- mate connectors 235
- loft 216
- export 209
- api 200
- dimensions 199
- extrude 196
- sketching 195
- voting 187
- variables 180
- improvement requests 174
- mates 162